Testers, Handheld Digital Multimeters (DMMs)
Hioki makes available information about inquiries from customers.
- Digital Multimeters, 4-1/2 Digit
- Digital Multimeters, 3-1/2 Digit
- Compact Digital Multimeters
- Analog Multimeters
- DC High Voltage Measurement (When Using a Dedicated Probe)
Digital Multimeters, 4-1/2 Digit
- Windows 10 compatibility
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- What communications commands are available when using the DT4900-01 to communicate with a computer?
- Difference between True RMS and MEAN testers
- Setging a threshold for continuity check on a DMM
- Meaning of "count" on digital multimeters?
- Measuring a DC signal with ripple
- Zero adjustment procedures of the DT4200 series
- DT series selection guide
- Communication command to use the DT4900-01
- DMM for inverter output voltage measurement
- Measuring current using the DT4281 and 9010-50 (clamp)
- Negative resistance value on a DMM
- Test tools with fuse protection
- What does CAT III, CAT IV mean?
- Full-wave rectified waveform (half-wave rectified waveform) Measurement (Tester, Clamp Meter)
- What is the measurable range of the Digital Multimeter (tester)?
Digital Multimeters, 3-1/2 Digit
- Measurement of the secondary side of an inverter
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- New standard for test probes
- What communications commands are available when using the DT4900-01 to communicate with a computer?
- Difference between True RMS and MEAN testers
- Setging a threshold for continuity check on a DMM
- Meaning of "count" on digital multimeters?
- Measuring a DC signal with ripple
- Zero adjustment procedures of the DT4200 series
- DT series selection guide
- Communication command to use the DT4900-01
- DMM for inverter output voltage measurement
- Negative resistance value on a DMM
- Conditions required for safe measurement of voltage exceeding 1000V DC [ DMMs, Clamp on meters ]
- What does CAT III, CAT IV mean?
- What is the measurable range of the Digital Multimeter (tester)?
Compact Digital Multimeters
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Setging a threshold for continuity check on a DMM
- Meaning of "count" on digital multimeters?
- DT series selection guide
- What does CAT III, CAT IV mean?
Analog Multimeters
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Please tell me about the internal resistance of analog testers.
- The polarity (+/-) was reversed when I made a measurement using the resistance range. Is the instrument broken?
- Getting 22.5V batteries for old testers like the OL64 and AF-105, etc.
- What does CAT III, CAT IV mean?
- Protective fuse