POWER QUALITY ANALYZER PW3198

3-Phase 4-Wire Power Quality Analyzer Compliant to IEC61000-4-30 Class A Standards with Dynamic 1300V Range, Harmonic and Inter-harmonics Analysis Capabilities

Discontinued

POWER QUALITY ANALYZER PQ3198

Overview
Specifications
Options
Downloads

Hioki portable power meters and analyzers are best in class power measuring instruments for measuring single to three-phase lines with a high degree of precision and accuracy. The PW3198 is a power quality analyzer for monitoring and recording power supply anomalies, allowing their causes to be quickly investigated, and also for assessing power supply problems such as voltage drops, flicker, harmonics, and other electrical issues.

Product Video

Key Features

Verify power problems in accordance with the IEC61000-4-30 Class A standard
High accuracy and continuous gapless recording
(V: ±0.1% of nominal voltage, A and W: ±0.2% rdg. ±0.1% f.s.)
CAT IV 600V - safe enough for incoming power lines
Broadband voltage range lets you measure even high-order harmonic components of up to 80 kHz
Wide dynamic range from low voltages up to 1300V (3P4W line-to-line voltage)
Maximum 6000V transient overvoltage up to 700kHz
LAN, USB and SD card interfaces
Optional GPS BOX for synchronizing multiple devices

Model No. (Order Code)

PW3198	Discontinued, Main unit, current sensor is sold separately
PW3198-90	Discontinued, Kit includes software the 9624-50

Note: Voltage can be measured with the main unit alone. An optional current sensor is necessary to measure current or power parameters. Use the PQA-HiView Pro 9624-50 (version 2.00 or later) with a PC to analyze the data collected to the SD card.

Basic specifications

Accuracy guaranteed: 1 year

Measurement line type	Single-phase 2-wire, Single-phase 3-wire, Three-phase 3-wire or Three-phase 4-wire plus one extra input channel (must be synchronized to reference channel during AC/DC measurement)
Voltage ranges	Voltage measurement: 600.00 V rms Transient measurement 6.0000 kV peak
Current ranges	500.00 mA to 5.0000 kA AC (depends on current sensor in use)
Power ranges	300.00 W to 3.0000 MW (determined automatically based on voltage and current range in use)
Basic accuracy	Voltage: ±0.1% of nominal voltage Current: ±0.2 % rdg. ±0.1 % f.s. + current sensor accuracy Active power: ±0.2 % rdg. ±0.1 % f.s. + current sensor accuracy
Measurement items	1. Transient over voltage : 2 MHz sampling 2. Frequency cycle : Calculated as one cycle, 40 to 70 Hz 3. Voltage (1/2) RMS: one cycle calculation refreshed every half cycle Current (1/2) RMS: half-cycle calculation 4. Voltage swell, Voltage dips, Voltage interruption 5. Inrush current 6. Voltage waveform comparison 7. Instantaneous flicker value: As per IEC61000-4-15 8. Frequency: Calculated as 10 or 12 cycles,40 to 70 Hz 9. 10-sec frequency: Calculated as the whole-cycle time during the specified 10 s period, 40 to 70 Hz 10. Voltage waveform peak, Current waveform peak 11. Voltage, Current, Active power, Apparent power, Reactive power, Active energy, Reactive energy, Power factor, Displacement power factor, Voltage unbalance factor, Current unbalance factor (negative-phase, zero-phase) 12. High-order harmonic component (voltage/ current): 2 kHz to 80 kHz 13. Harmonic/ Harmonic phase angle (voltage/ current), Harmonic power: 0th to 50 th orders 14. Harmonic voltage-current phase angle: 1th to 50 th orders 15. Total harmonic distortion factor (voltage/ current) 16. Inter harmonic (voltage/ current): 0.5 th to 49.5 th order 17. K Factor (multiplication factor) 18. IEC Flicker, Δ V10 Flicker
Record	55 weeks (with repeated recording set to [1 Week], 55 iterations) 35 days (with repeated recording set to [OFF])
Interfaces	SD/SDHC memory card, RS-232C, LAN (HTTP server funtion), USB2.0
Display	6.5-inch TFT color LCD (640 × 480 dots)
Power supply	AC Adapter Z1002 (12 V DC, Rated power supply 100 V AC to 240 V AC, 50/60 Hz) Battery Pack Z1003 (Ni-MH 7.2 V DC 4500 mAh)
Dimensions and mass	300 mm (11.81 in) W × 211 mm (8.31 in) H × 68 mm (2.68 in) D (excluding protrusions), 2.6 kg (91.7 oz) (including battery pack)
Included accessories	Instruction manual ×1, Measurement guide ×1, Voltage cord L1000 ×1 set (Red/Yellow/Blue/Gray, each 1, Black ×4, Alligator clip ×8), Spiral tube ×20, Input Cable Labels ×1, AC adapter Z1002 ×1, Strap ×1, USB cable (1 m 3.28 ft length) ×1, Battery pack Z1003 ×1, SD memory card 2GB Z4001 ×1

Current input (8)

For power or load current measurement

(1 sensor necessary for single-phase measurements, and 2 or 3 sensors required for 3-phase measurements)

AC FLEXIBLE CURRENT SENSOR CT9667

Learn more

• 10 Hz to 20 kHz, ±2% accuracy
• Rated 5000 A/ 500 A AC

CONNECTION CABLE 9219

Connect with the 9695-02/ -03, Output BNC terminal, 3m (9.84ft) length

CLAMP ON SENSOR 9660

Learn more

• 40Hz to 5kHz, ±0.3% accuracy
• Rated 100 A AC, 1 mV/A output rate

CLAMP ON SENSOR 9661

Learn more

• 40Hz to 5kHz, ±0.3% accuracy
• Rated 500 A AC, 1 mV/A output rate

CLAMP ON SENSOR 9669

Learn more

• 40Hz to 5kHz, ±1.0% accuracy
• Rated 1000 A AC, 0.5 mV/A output rate

CLAMP ON SENSOR 9694

Learn more

• 40Hz to 5kHz, ±0.3% accuracy
• Rated 5 A AC, 10 mV/A output rate

CLAMP ON SENSOR 9695-02

Learn more

• 40Hz to 5kHz, ±0.3% accuracy
• Rated 50 A AC, 10 mV/A output rate

CLAMP ON SENSOR 9695-03

Learn more

• 40Hz to 5kHz, ±0.3% accuracy
• Rated 100 A AC, 1 mV/A output rate

Leak current input (2)

Caution: Up to 5 A on Model PW3198

*Not capable of power measurement

CLAMP ON LEAK SENSOR 9657-10

Learn more

• 40 Hz to 5 kHz, ±1.0 accuracy
• Rated 10 A AC, 100 mV/A output rate

CLAMP ON LEAK SENSOR 9675

Learn more

• 40 Hz to 5 kHz, ±1.0% accuracy
• Rated 10 A AC, 100 mV/A output rate

Adapter (1)

For clamp sensor

CLAMP ON ADAPTER 9290-10

Learn more

• Primary 1000A, secondary 100A (1/10 ratio) output
• Superior phase angle characteristics for power

AC/DC Current input (6)

*The AC/DC Auto-zero Current Sensor CT7731/CT7736/CT7742 cannot be used on its own with the PW3198. Be sure to use a set that includes the Display Unit CM7290, Output Cord L9095, and AC Adapter 9445-02 or 9445-03.

DISPLAY UNIT CM7290

Learn more

• Pair with CT7000 series
• DCA, ACA, (DC+AC)A, frequency
• WAVE, RMS, PEAK, Hz output

AC/DC AUTO-ZERO CURRENT SENSOR CT7731

Learn more

• DC to 5 kHz, ±1.0% accuracy
• Rated 100A AC/DC

AC/DC AUTO-ZERO CURRENT SENSOR CT7736

Learn more

• DC to 5 kHz, ±2.0% accuracy
• Rated 600A AC/DC

AC/DC AUTO-ZERO CURRENT SENSOR CT7742

Learn more

• DC to 5 kHz, ±1.5% accuracy
• Rated 2000A AC/DC

OUTPUT CORD L9095

Connect to BNC terminal, 1.5 m (4.92 ft) length

AC ADAPTER 9445-02

For USA, 100 to 240 V AC, 9 V/ 1 A

Voltage input (6)

*The L1000 is bundled

VOLTAGE CORD L1000

Red/ Yellow/ Blue/ Gray each 1, Black 4, 3m (9.84ft) length, Alligator clip ×8

GRABBER CLIP L9243

Attaches to the tip of the banana plug cable, Red/Black: 1 each, 185 mm (7.28 in.) length, CAT II 1000 V

WIRING ADAPTER PW9000

When three-phase 3-wire connection, the voltage cord to be connected can be reduced from 6 to 3

WIRING ADAPTER PW9001

When three-phase 4-wire connection, the voltage cord to be connected can be reduced from 6 to 4

MAGNETIC ADAPTER 9804-01

Attaches to the tip of cord, red ×1, φ11 mm (0.43 in)

MAGNETIC ADAPTER 9804-02

Attaches to the tip of cord, black ×1, φ11 mm (0.43 in)

Power supply (2)

*The Z1002, Z1003 are bundled

AC ADAPTER Z1002

For main unit, 100 to 240 V AC

BATTERY PACK Z1003

NiMH, Charges while installed in the main unit

Storage media (2)

*The Z4001 is bundled

SD Card Precaution
Use only the SD Card Z4001 sold by HIOKI. Compatibility and performance are not guaranteed for SD cards made by other manufacturers. You may be unable to read from or save data to such cards.