Search Results
Results of search is 5195 hits.
-
Is an isolation transformer required for leakage current testers?
https://www.hioki.com/sg-en/support/faq/detail/id_n1020979
Why are isolation transformers used in leakage current measurements of medical and general electrical equipments? (Leak Current HiTester ST5540)
-
The measured value display does not indicate “Lo” when the voltage sensor is not attached to a wire.
https://www.hioki.com/sg-en/support/faq/detail/id_181
The measured value display does not indicate “Lo” when the voltage sensor is not attached to a wire.
-
Measured values exhibit instability.
https://www.hioki.com/sg-en/support/faq/detail/id_179
Measured values exhibit instability.
-
The probe responds briefly when moved towards and away from a non-energized circuit or a DC circuit.
https://www.hioki.com/sg-en/support/faq/detail/id_178
The probe responds briefly when moved towards and away from a non-energized circuit or a DC circuit.
-
Can the MR8904 output data to the CAN bus?
https://www.hioki.com/sg-en/support/faq/detail/id_175
Can the MR8904 output data to the CAN bus?
-
When connecting the MR8875 to a PC with a LAN cable, how long can the cable be?
https://www.hioki.com/sg-en/support/faq/detail/id_171
When connecting the MR8875 to a PC with a LAN cable, how long can the cable be?
-
Can the instrument calculate the mean every minute while recording data?
https://www.hioki.com/sg-en/support/faq/detail/id_168
Can the LR8431 calculate the mean every minute while recording data?
-
When Bluetooth communications are restored, can data captured while they were interrupted be transferred to the LR8410?
https://www.hioki.com/sg-en/support/faq/detail/id_167
When Bluetooth communications are restored, can data captured while they were interrupted be transferred to the LR8410?
-
I’d like to measure a high-capacity EDLC’s ESR at 100 Hz and 1 kHz.
https://www.hioki.com/sg-en/support/faq/detail/id_165
I’d like to measure a high-capacity EDLC’s ESR at 100 Hz and 1 kHz.
-
Are the Rhc and Rhp output resistors shown in the reference circuit in Appendix 5.2 of the user manual built into the instrument?
https://www.hioki.com/sg-en/support/faq/detail/id_164
Are the Rhc and Rhp output resistors shown in the reference circuit in Appendix 5.2 of the user manual built into the instrument?
-
Breakdown voltage testing with the WT-8752 sometimes stops partway through. What could be causing this issue?
https://www.hioki.com/sg-en/support/faq/detail/id_162
Breakdown voltage testing with the WT-8752 sometimes stops partway through. What could be causing this issue?
-
What range of measured currents can be used when connecting two current probes to the Power Supply for Current Probes 3272?
https://www.hioki.com/sg-en/support/faq/detail/id_154
What range of measured currents can be used when connecting two current probes to the Power Supply for Current Probes 3272?
-
Will measuring a current in excess of the maximum input current damage the probe?
https://www.hioki.com/sg-en/support/faq/detail/id_153
Will measuring a current in excess of the maximum input current damage the probe?
-
What is the difference between the transient voltage and the voltage waveform peak?
https://www.hioki.com/sg-en/support/faq/detail/id_151
What is the difference between the transient voltage and the voltage waveform peak?
-
Measuring 1700 V DC with a clamp meter and bundled test leads
https://www.hioki.com/sg-en/support/faq/detail/id_150
My clamp meter can measure up to 1700 V DC, but can that voltage be measured with the included test leads?
-
How can I record a longer event waveform?
https://www.hioki.com/sg-en/support/faq/detail/id_149
How can I record a longer event waveform?
-
About panel load times
https://www.hioki.com/sg-en/support/faq/detail/id_148
Please tell me about panel load times.
-
Unable to communicate with LCR meter via LAN
https://www.hioki.com/sg-en/support/faq/detail/id_146
I’ve connected a computer (PLC) and LCR meter via the LAN interface but am unable to get
the two devices to communicate properly. Please advise what I should check. -
Unable to communicate with LCR meter via GP-IB
https://www.hioki.com/sg-en/support/faq/detail/id_145
I’ve connected a computer (PLC) and LCR meter via the GP-IB interface but am unable to get
the two devices to communicate properly. Please advise what I should check. -
Unable to communicate with LCR meter via USB
https://www.hioki.com/sg-en/support/faq/detail/id_144
I’ve connected a computer (PLC) and LCR meter via the USB interface but am unable to get
the two devices to communicate properly. Please advise what I should check.