Search Results

・ 2 port, CAN signal (CAN FD is not supported)
・ 15 analog ch equivalent
・ 16 logic ch equivalent

2 port, CAN signal (CAN FD is not supported)15 analog ch equivalent

• 16 ch, logic signal
• Up to four logic probes

• 2 ch, high resolution measurement
• DC to 100 kHz bandwidth

2 ch, high resolution DC to 100 kHz bandwidth

• 2 ch, instantaneous waveform/RMS
• DC to 400 kHz bandwidth
• RMS: DC and 30 to 100 kHz

2 ch, instantly waveform/RMS DC to 400 kHz bandwidth

• 4 ch, acceleration, load, pressure or strain
• Strain gauge converter amp

4 ch, acceleration, load, pressure or strain Strain gauge converter amp

• For Hioki Data Loggers and Memory HiLoggers
• Software for CAN unit settings
• Receive channel definition settings
• Save and load CAN bus definition files

View a trend graph and scroll back to view earlier waveform data, even while recording

• 2 ch, instantaneous waveforms
• DC to 5 MHz bandwidth

2 ch, instantly waveforms DC to 5 MHz bandwidth

• 2 ch, measuring current
• DC to 100 kHz bandwidth
• Directly connectable with current sensors

• Wide-frequency Memory HiCorder input unit with 12-bit A/D resolution

• DC to 8MHz, 50Ω termination
• Tip electrode spacing: 0.3 to 6 mm
• Measurable sample sizes: 0201 to 2220 (inch)

• 2-wire probe for LCR testing of small chip components

• 2 ch, temperature
• Thermocouple input

2 ch, Temperature Thermocouple input

• 2 ch, rotation, frequency
• DC to 100 kHz

• 15 ch, minute voltage, temperature
• Voltage/Thermocouple measurement

15 ch, minute voltage, temperature Voltage/Thermocouple

• For direct connection two-wire testing
• DC to 3 GHz
• 6 measurable sample sizes: 0201 to 1210 (inch)

• Test fixture for IM7580 series Impedance Analyzers
• High frequency analysis

• 4 ch, voltage input
• DC to 100kHz bandwidth

4 ch, voltage input DC to 100kHz bandwidth

• 600.0 mV to 1000 V DC/6.000 V to 1000 V AC
• 60μA to 60mA DC
• AC Current measurement with clamp-on probe

• 6000 count DMM for measuring HVAC equipment and gas-burning devices in facilities maintenance
• Test from instrumentation signals to flame currents (60μA DC)

• DC to 50 MHz (−3dB), ±3.0% accuracy
• Maximum 5 A rms
• ±7.5 A peak (non-continuous)

• High-sensitivity for observing minute currents down to 1 mA
• Ideal for developing switching power supplies, inverts and motor controllers
• High S/N ratio

・DC1000V, up to 1 × 10^16 Ω, DUT 40 - 100 mm (≤8 mm thick)
・Not CE Marked
Note: DSM8104F required

・Measure the resistivity of flat samples efficiently
・Option for the SM7000 Series Super Megohmmeters

• 1 Hz to 100 kHz, ±0.3% accuracy
• Rated 20 A/200 A AC

• Measuring AC current with low frequencies such as inverter control devices
• Wide bandwidth ideal for harmonic analysis, FFT analysis and waveform monitoring

• 2ch logger, minimum 0.5 sec interval
• Log temperature and humidity
• Transfer data wirelessly to mobile device or PC

• - 40 °C to 80 °C/ 0% to 100 % RH (with optional sensor)
• Manage production plants and agricultural sites

• |Z|, L, C, R testing
• 1 mHz to 200 kHz
• 2 ms test speed, ±0.05% accuracy
• Transformer measurement mode

• Built-in low impedance high precision mode for testing low inductance or ESR of aluminum electrolysis capacitance
• Turn ratio, mutual inductance and inductance difference measurements of transformers and coils