BATTERY HiTESTER BT3563A
Fully Automated Production Line Testing of Large Packs for xEVs or Large Packs of up to 300 V
- Simultaneous measurement of internal resistance and open circuit voltage.
- Fully automated production line testing of large packs for xEVs or large packs of up to 300 V.
- Resistance measurement ranges: 3 mΩ/30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ
- Voltage measurement ranges: 6 V/60 V/300 V
- Equipped with LAN
Model No. (Order Code)
Measuring battery performance and safety using internal resistance (AC-IR) and open-circuit voltage (OCV)
Inspect the quality of completed cells, modules, and packs on production lines. Measure internal resistance (AC-IR) and open-circuit voltage (OCV) to check battery quality. Cells produced at the cell production factory are shipped to the module production factory after undergoing a shipping inspection. Since factors such as vibrations during shipment and even the passage of time can cause defects, batteries undergo an acceptance inspection before being assembled into modules and packs.
Small cells for power motors, Small packs of up to 60 V
Voltage measurement ranges: 6 V/60 V
Resistance measurement ranges: 30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ
Large cells for xEVs, Mid-sized packs of up to 100 V
Voltage measurement ranges: 6 V/60 V/100 V
Resistance measurement ranges: 3 mΩ/30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ
Large packs for xEVs, Large packs of up to 300 V
Voltage measurement ranges: 6 V/60 V/300 V
Resistance measurement ranges: 3 mΩ/30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ
Reducing test system development cost and management man-hours
The new BT356xA has dramatically improved tolerances for line resistance compared to previous models. This improvement makes it easy to build test systems with large numbers of channels using relays. Additionally, a longer maintenance cycle for systems in use means fewer maintenance man-hours. Finally, its capability to handle thinner cables than with previous models* makes it easier to route cables.
*AWG 29 (0.064 mm2) wire equivalent to 2.2 Ω over
an 8 m round trip can be used with the 3 mΩ or 30 mΩ range.
Improve Productivity by Increasing the Number of Inspection Channels
You can use the Switch Mainframe SW1001/SW1002 to increase the number of measurement channels. Additionally, you can perform scan measurement by controlling two instruments at once, for example a BT356xA series instrument and a DM7276, or a BT4560 and a DM7276.
Preventing instrument malfunctions caused by static electricity
Batteries can become charged on production lines, for example, when being transported on a conveyor belt. When probes are placed in contact with such batteries, the resulting application of static electricity can then damage the instrument. The BT356xA series is designed to withstand contact with ±30 kV of static electricity*, preventing static-caused malfunctions and reducing testing line downtime.
* ±30 kV IEC 61000-4-2 contact discharge
LAN interface as standard
The BT356xA series is equipped with a LAN interface as standard equipment, making it easy for the instrument to interoperate with a PLC*-based control system. The ability to use readily accessible LAN cables helps lower costs during system development and maintenance. Furthermore, a design with strong noise and static electricity resistance helps avoid system problems.
*Programmable Logic Controller, a device that automatically controls one or more machines
The De Facto Standard of Battery Testers
The HIOKI BT356xA series
These highly advanced battery testers are best suited for shipping and acceptance inspections of cells and battery packs. They simultaneously measure internal resistance and the battery’s open-circuit voltage (OCV).
Since the AC-IR measurement method is used, the measurement time is shortened. In addition, highly repeatable results are attained with this method. These testers have a highly accurate 3 mΩ range, allowing for a resistance measurement of battery tab welding and bus bars. All of this combines for the best choice in battery testers.
High input voltage applications The input high voltage (1,000 V) model, BT3564, can measure the total resistance of the battery whole pack at once.
*Watch with the video subtitles on, to see detailed descriptions.
|Resistance measurement ranges||3 mΩ（Max. display: 3.1000 mΩ, resolution: 0.1 μΩ, measurement current: 100 mA）
30 mΩ（Max. display: 31.000 mΩ, resolution: 1 μΩ, measurement current: 100 mA）
300 mΩ（Max. display: 310.00 mΩ, resolution: 10 μΩ, measurement current: 10 mA）
3 Ω（Max. display: 3.1000 Ω, resolution: 100 μΩ, measurement current: 1 mA）
30 Ω（Max. display: 31.000 Ω, resolution: 1 mΩ, measurement current: 100 μA）
300 Ω（Max. display: 310.00 Ω, resolution: 10 mΩ, measurement current: 10 μA）
3 kΩ（Max. display: 3.1000 kΩ, resolution: 100 mΩ, measurement current: 10 μA）
Basic accuracy: ±0.5% rdg ±10 dgt（3 mΩ range）, ±0.5% rdg ±5 dgt（30 mΩ range or more）
Measurement frequency: 1 kHz ±0.2 Hz
Measurement method: AC four-terminal method
|Voltage measurement ranges||6 V（Max. display: 6.00000 V, resolution: 10 μV）
60 V（Max. display: 60.0000 V, resolution: 100 μV）
300 V（Max. display: 300.000 V, resolution: 1 mV）
Basic accuracy: ±0.01% rdg. ±3 dgt.
|Response time||10 ms|
|Sampling period||Ω or V (60 Hz): 4 ms (EX.FAST), 12 ms (FAST), 35 ms (MEDIUM), 150 ms (SLOW)
ΩV (60 Hz): 8 ms (EX.FAST), 24 ms (FAST), 70 ms (MEDIUM), 253 ms (SLOW)
Ω or V (50 Hz): 4 ms (EX.FAST), 12 ms (FAST), 42 ms (MEDIUM), 157 ms (SLOW)
ΩV (50 Hz): 8 ms (EX.FAST), 24 ms (FAST), 84 ms (MEDIUM), 259 ms (SLOW)
|Functions||Contact check, Zero adjustment (±1000 counts), Pulse measurement, Comparator (Hi/ IN/ Lo), Statistical calculations (Max. 30,000), Delay, Average, Panel saving/loading, Memory storage, LabVIEW® driver|
|Interfaces||LAN (TCP/IP, 10BASE-T/100BASE-TX)
RS-232C (Max. 38.4 kbps, Available as printer I/F)
EXT I/O (37-pin Handler interface)
Analog output (DC 0 V to 3.1 V)
|Power supply||100 to 240 V AC, 50 Hz/60 Hz, 35 VA max.|
|Dimensions and mass||215 mm (8.46 in) W × 80 mm (3.15 in) H × 295 mm (11.61 in) D, 2.4 kg (84.7 oz)|
|Included accessories||Instruction manual ×1, Power cord ×1, Operating Precautions ×1|
Measurement leads (for measuring high voltage batteries) (3)
To replace the tip on the Pin type lead 9772, L2100/L2110, Pin type lead L2003,(one piece)
A: 300 mm (11.81 in.), B: 172 mm (6.77 in.), L: 1400 mm (4.59 ft.), for high voltage battery measurements, 1000 V DC max.
A: 750 mm (29.53 in.), B: 215 mm (8.46 in.), L: 1880 mm (6.17 ft.), for high voltage battery measurements, 1000 V DC max.
Measurement Leads (for measuring batteries up to 60 V with small electrodes) (1)
1.8 mm dia. single-axis type
A: 260 mm (10.24 in.), B: 140 mm (5.51 in.), L: 850 mm (2.79 ft.), 60 V DC
Measurement Leads (for measuring batteries up to 60 V at thru holes and sub-millimeter objects) (1)
0.2 mm parallel pyramid-type pins
A: 260 mm (10.24 in.), B: 138 mm (5.43 in.), L: 850 mm (2.79 ft.), 60 V DC
Measurement Leads (for measuring batteries up to 60 V, others) (3)
A: 300 mm (11.81 in.), B: 131 mm (5.16 in.), L: 1350 mm (53.15 in.), tip φ 28 mm (1.10 in.), 50 V DC
A: 130 mm (5.12 in.), B:84 mm (3.31 in.), L:1.1 m (3.61 ft.), 60 V DC
A: 280 mm (11.02 in.), B: 118 mm (4.65 in.), L: 1360 mm (4.46 ft.), 60 V DC
Zero adjustment board (1)
Can not be used for Pin Type Lead 9770 and Pin Type Lead 9771
For L2100, L2110, L2020, 9465-10, 9772
PC communication (1)
9 pin - 9 pin, cross, 1.8 m (5.91 ft) length