Search Results
Results of search is 5172 hits.
-
What communications commands are available when using the DT4900-01 to communicate with a computer?
https://www.hioki.com/us-en/support/faq/detail/id_195
What communications commands are available when using the DT4900-01 to communicate with a computer?
-
Can the two units that are included with the LR8400 be removed?
https://www.hioki.com/us-en/support/faq/detail/id_193
Can the two units that are included with the LR8400 be removed?
-
Is it possible to measure the leakage current of a 3-phase/3-wire or 3-phase/4-wire device?
https://www.hioki.com/us-en/support/faq/detail/id_191
Is it possible to measure the leakage current of a 3-phase/3-wire or 3-phase/4-wire device?
-
I’m seeing voltage measured values that are lower than the nominal voltage.
https://www.hioki.com/us-en/support/faq/detail/id_190
I’m seeing voltage measured values that are lower than the nominal voltage.
-
Is the following connection method correct: OUTPUT terminal + coaxial cable + 50 Ω terminating resistor + measuring instrument?
https://www.hioki.com/us-en/support/faq/detail/id_189
Is the following connection method correct: OUTPUT terminal + coaxial cable + 50 Ω terminating resistor + measuring instrument?
-
Can I change the full-scale value by changing the CT ratio? Will the accuracy and resolution change as a result?
https://www.hioki.com/us-en/support/faq/detail/id_188
Can I change the full-scale value by changing the CT ratio? Will the accuracy and resolution change as a result?
-
What is the smallest current value that can be measured with wideband current probes?
https://www.hioki.com/us-en/support/faq/detail/id_186
What is the smallest current value that can be measured with Hioki wideband current probes?
-
What is two-point (two-pole) method of Earth Tester?
https://www.hioki.com/us-en/support/faq/detail/id_n1021221
What is the 2-point (2-pole) measurement method of Earth Tester FT6031-50?
-
Is it possible to measure power in multiple circuits using the same voltage circuit?
https://www.hioki.com/us-en/support/faq/detail/id_185
Is it possible to measure power in multiple circuits using the same voltage circuit?
-
Beep(ing) sound settings of Leak Current HiTester
https://www.hioki.com/us-en/support/faq/detail/id_n1021121
I've just got my Leak Current HiTester ST5540 back from calibration.
Beeping sound occurs even though it is PASS. What should I do? -
Is an isolation transformer required for leakage current testers?
https://www.hioki.com/us-en/support/faq/detail/id_n1020979
Why are isolation transformers used in leakage current measurements of medical and general electrical equipments? (Leak Current HiTester ST5540)
-
The measured value display does not indicate “Lo” when the voltage sensor is not attached to a wire.
https://www.hioki.com/us-en/support/faq/detail/id_181
The measured value display does not indicate “Lo” when the voltage sensor is not attached to a wire.
-
Measured values exhibit instability.
https://www.hioki.com/us-en/support/faq/detail/id_179
Measured values exhibit instability.
-
The probe responds briefly when moved towards and away from a non-energized circuit or a DC circuit.
https://www.hioki.com/us-en/support/faq/detail/id_178
The probe responds briefly when moved towards and away from a non-energized circuit or a DC circuit.
-
Can the MR8904 output data to the CAN bus?
https://www.hioki.com/us-en/support/faq/detail/id_175
Can the MR8904 output data to the CAN bus?
-
When connecting the MR8875 to a PC with a LAN cable, how long can the cable be?
https://www.hioki.com/us-en/support/faq/detail/id_171
When connecting the MR8875 to a PC with a LAN cable, how long can the cable be?
-
Can the instrument calculate the mean every minute while recording data?
https://www.hioki.com/us-en/support/faq/detail/id_168
Can the LR8431 calculate the mean every minute while recording data?
-
When Bluetooth communications are restored, can data captured while they were interrupted be transferred to the LR8410?
https://www.hioki.com/us-en/support/faq/detail/id_167
When Bluetooth communications are restored, can data captured while they were interrupted be transferred to the LR8410?
-
I’d like to measure a high-capacity EDLC’s ESR at 100 Hz and 1 kHz.
https://www.hioki.com/us-en/support/faq/detail/id_165
I’d like to measure a high-capacity EDLC’s ESR at 100 Hz and 1 kHz.
-
Are the Rhc and Rhp output resistors shown in the reference circuit in Appendix 5.2 of the user manual built into the instrument?
https://www.hioki.com/us-en/support/faq/detail/id_164
Are the Rhc and Rhp output resistors shown in the reference circuit in Appendix 5.2 of the user manual built into the instrument?