Current Probes/Sensors, Voltage Probes, CAN Sensors
Hioki makes available information about inquiries from customers.
- Non-contact Voltage Probe, Non-contact CAN Sensors
- Current Waveform Observation
- High Accuracy Pass-through
- AC/DC Current Sensors, DC to 20 kHz
- AC Current Sensors, up to 50 kHz
- Load Current Sensors
- Power Supplies for Current Sensors
- High Accuracy Clamps
- High Accuracy Direct Connection
Non-contact Voltage Probe, Non-contact CAN Sensors
- Second hand instruments
- Difference between the Non-Contact CAN Sensor SP7001 and SP7002
- The non-contact CAN sensor is connected to the CAN analysis tool, but the CAN data cannot be acquired
Current Waveform Observation
- Leaving Clamp on Sensors in connecting to the Clamp on Power Meter
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Use of PCB (Poly Chlorinated Biphenyl) content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Clamp sensor voltage to earth
- My oscilloscope’s input impedance can be switched between 1 MΩ and 50 Ω. Can I use either setting?
- Will measuring a current in excess of the maximum input current damage the probe?
- What range of measured currents can be used when connecting two current probes to the Power Supply for Current Probes 3272?
- What is the smallest current value that can be measured with wideband current probes?
- Input exceeding the derating
- Effect of external magnetic field on clamp on sensors
- WLTP (Worldwide harmonized Light vehicles Test Procedure) measurement using the PW3390
- Effect of input impedance to use with an oscilloscope [Clamp on Probes, Clamp on Sensors]
- Dividing output [Clamp on Probes, Current Sensors]
- Overvoltage categories for Clamp on Probes and Current Sensors
- Current probe time skew
- User's Guide "Current Measurement Method for Electric Wires with Shielding"
- Derating in the specifications of current sensors/probes
High Accuracy Pass-through
- Leaving Clamp on Sensors in connecting to the Clamp on Power Meter
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Use of PCB (Poly Chlorinated Biphenyl) content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Clamp sensor voltage to earth
- What effect does increasing the number of turns in the measured wire have on measurement error?
- Can I change the full-scale value by changing the CT ratio? Will the accuracy and resolution change as a result?
- Input exceeding the derating
- Effect of external magnetic field on clamp on sensors
- WLTP (Worldwide harmonized Light vehicles Test Procedure) measurement using the PW3390
- Effect of input impedance to use with an oscilloscope [Clamp on Probes, Clamp on Sensors]
- Dividing output [Clamp on Probes, Current Sensors]
- Overvoltage categories for Clamp on Probes and Current Sensors
- User's Guide "Current Measurement Method for Electric Wires with Shielding"
- Derating in the specifications of current sensors/probes
AC/DC Current Sensors, DC to 20 kHz
- Leaving Clamp on Sensors in connecting to the Clamp on Power Meter
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Use of PCB (Poly Chlorinated Biphenyl) content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Input exceeding the derating
- Effect of external magnetic field on clamp on sensors
- WLTP (Worldwide harmonized Light vehicles Test Procedure) measurement using the PW3390
- Effect of input impedance to use with an oscilloscope [Clamp on Probes, Clamp on Sensors]
- Dividing output [Clamp on Probes, Current Sensors]
- Difference between the CT6904 and CT6876
- Overvoltage categories for Clamp on Probes and Current Sensors
- User's Guide "Current Measurement Method for Electric Wires with Shielding"
- Derating in the specifications of current sensors/probes
- After starting measurement, the screen display disappears (CM7290)
- Current measurement including multiple frequency components (Current sensor)
AC Current Sensors, up to 50 kHz
- Leaving Clamp on Sensors in connecting to the Clamp on Power Meter
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Use of PCB (Poly Chlorinated Biphenyl) content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Clamp sensor voltage to earth
- Input exceeding the derating
- Difference between the 9667 and CT9667
- Effect of external magnetic field on clamp on sensors
- Effect of input impedance to use with an oscilloscope [Clamp on Probes, Clamp on Sensors]
- Dividing output [Clamp on Probes, Current Sensors]
- Overvoltage categories for Clamp on Probes and Current Sensors
- Derating in the specifications of current sensors/probes
- After starting measurement, the screen display disappears (CM7290)
- Difference between Clamp on Probe 9010-50 and Clamp on Probe 9018-50
- Current output function of the sensor unit
Load Current Sensors
- Leaving Clamp on Sensors in connecting to the Clamp on Power Meter
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Use of PCB (Poly Chlorinated Biphenyl) content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Clamp sensor voltage to earth
- Difference between the 9667 and CT9667
- Effect of external magnetic field on clamp on sensors
- Clamp on meters that use AC flexible sensors
- Measuring leakage current with a flexible current sensor
Power Supplies for Current Sensors
- Compliance to the RoHS2 Directive (10 restricted substances)
- Pollution Degree
- Calibration at a specific point
- ISO/IEC17025 accredited calibration
- Use of mercury content
- Use of PCB (Poly Chlorinated Biphenyl) content
- Production date and serial number
- Want SDS: Safety Data Sheet (MSDS: Material Safety Data Sheet)
- Second hand instruments
- Is the following connection method correct: OUTPUT terminal + coaxial cable + 50 Ω terminating resistor + measuring instrument?
- Difference between models CT6841-50 and CT6841A (Current Sensor)