Search Results

Results of search is 5191 hits.

Wiring check on Clamp-on Power Meters

https://www.hioki.com/global/support/faq/detail/id_204

The wiring check of the Clamp-on Power HiTESTER 3169 does not give "OK", though the wiring is correct. Is it OK to measure under this condition?
Convert the 3196's text mode data to binary data

https://www.hioki.com/global/support/faq/detail/id_203

I measured power quality in text mode of the 3196 by mistake. Is there any way to convert the data to binary data to analyze on the PQA HiVEW Pro 9624-50?
How to read "Status" data of the 3197

https://www.hioki.com/global/support/faq/detail/id_202

How do I read the Status data in the 3197's TIME PLOT data (97intvl.csv)?
The 3197 Application displays "Cannot open the file."

https://www.hioki.com/global/support/faq/detail/id_201

The 3197 Application displays the message "Cannot open the file."
3196 and 9624-50 Compatibility

https://www.hioki.com/global/support/faq/detail/id_197

Is the 9624-50 PQA HiView Pro compatible with the discontinued 3196 Power Quality Analyzer?
PW3198 and 9624-10 Compatibility

https://www.hioki.com/global/support/faq/detail/id_196

Is the discontinued 9624-10 PQA HiView Pro software compatible with PW3198 Power Quality Analyzer?
What communications commands are available when using the DT4900-01 to communicate with a computer?

https://www.hioki.com/global/support/faq/detail/id_195

What communications commands are available when using the DT4900-01 to communicate with a computer?
Can the two units that are included with the LR8400 be removed?

https://www.hioki.com/global/support/faq/detail/id_193

Can the two units that are included with the LR8400 be removed?
Is it possible to measure the leakage current of a 3-phase/3-wire or 3-phase/4-wire device?

https://www.hioki.com/global/support/faq/detail/id_191

Is it possible to measure the leakage current of a 3-phase/3-wire or 3-phase/4-wire device?
I’m seeing voltage measured values that are lower than the nominal voltage.

https://www.hioki.com/global/support/faq/detail/id_190

I’m seeing voltage measured values that are lower than the nominal voltage.
Is the following connection method correct: OUTPUT terminal + coaxial cable + 50 Ω terminating resistor + measuring instrument?

https://www.hioki.com/global/support/faq/detail/id_189

Is the following connection method correct: OUTPUT terminal + coaxial cable + 50 Ω terminating resistor + measuring instrument?
Can I change the full-scale value by changing the CT ratio? Will the accuracy and resolution change as a result?

https://www.hioki.com/global/support/faq/detail/id_188

Can I change the full-scale value by changing the CT ratio? Will the accuracy and resolution change as a result?
What is the smallest current value that can be measured with wideband current probes?

https://www.hioki.com/global/support/faq/detail/id_186

What is the smallest current value that can be measured with Hioki wideband current probes?
What is two-point (two-pole) method of Earth Tester?

https://www.hioki.com/global/support/faq/detail/id_n1021221

What is the 2-point (2-pole) measurement method of Earth Tester FT6031-50?
Is it possible to measure power in multiple circuits using the same voltage circuit?

https://www.hioki.com/global/support/faq/detail/id_185

Is it possible to measure power in multiple circuits using the same voltage circuit?
Beep(ing) sound settings of Leak Current HiTester

https://www.hioki.com/global/support/faq/detail/id_n1021121

I've just got my Leak Current HiTester ST5540 back from calibration.
Beeping sound occurs even though it is PASS. What should I do?
Is an isolation transformer required for leakage current testers?

https://www.hioki.com/global/support/faq/detail/id_n1020979

Why are isolation transformers used in leakage current measurements of medical and general electrical equipments? (Leak Current HiTester ST5540)
The measured value display does not indicate “Lo” when the voltage sensor is not attached to a wire.

https://www.hioki.com/global/support/faq/detail/id_181

The measured value display does not indicate “Lo” when the voltage sensor is not attached to a wire.
Measured values exhibit instability.

https://www.hioki.com/global/support/faq/detail/id_179

Measured values exhibit instability.
The probe responds briefly when moved towards and away from a non-energized circuit or a DC circuit.

https://www.hioki.com/global/support/faq/detail/id_178

The probe responds briefly when moved towards and away from a non-energized circuit or a DC circuit.

Select your region & language

Americas

Europe

East Asia

Southeast Asia, Oceania

India

Worldwide

Search Results

Wiring check on Clamp-on Power Meters

Convert the 3196's text mode data to binary data

How to read "Status" data of the 3197

The 3197 Application displays "Cannot open the file."

3196 and 9624-50 Compatibility

PW3198 and 9624-10 Compatibility

What communications commands are available when using the DT4900-01 to communicate with a computer?

Can the two units that are included with the LR8400 be removed?

Is it possible to measure the leakage current of a 3-phase/3-wire or 3-phase/4-wire device?

I’m seeing voltage measured values that are lower than the nominal voltage.

Is the following connection method correct: OUTPUT terminal + coaxial cable + 50 Ω terminating resistor + measuring instrument?

Can I change the full-scale value by changing the CT ratio? Will the accuracy and resolution change as a result?

What is the smallest current value that can be measured with wideband current probes?

What is two-point (two-pole) method of Earth Tester?

Is it possible to measure power in multiple circuits using the same voltage circuit?

Beep(ing) sound settings of Leak Current HiTester

Is an isolation transformer required for leakage current testers?

The measured value display does not indicate “Lo” when the voltage sensor is not attached to a wire.

Measured values exhibit instability.

The probe responds briefly when moved towards and away from a non-energized circuit or a DC circuit.