| Command | Data | Explanation | L
C
R | C
O
N
T
I
N
U
O
U
S |
|---|
Common Commands |
| *CLS | | Clearing the status byte register and related queues (except the output queue) |  | |
| *ESE | <Mask value> | Reading and writing the standard event status enable register (SESER) | | |
| *ESE? | |
| *ESR? | | Reading and clearing the standard event status register (SESR) | | |
| *IDN? | | Querying the instrument ID (Identification Code) | | |
| *OPC | | Setting OPC of SESR after all of the actions being executed are finished | | |
| *OPC? | | Sending response of ASCII 1 after all of the actions being executed are finished | | |
| *RST | | Initializing the instrument | | |
| *SRE | <Mask value> | Writing and reading the service request enable register (SRER) | | |
| *SRE? | |
| *STB? | | Reading the Status Byte Register | | |
| *TRG | | Requesting a Sample | | |
| *TST? | | Executing self tests and querying results | | |
| *WAI | | Executing following command after command processing is finished | | |
Event Registers |
| :ESE0 | <Mask value> | Writing and reading event status enable register 0 | | |
| :ESE0? | |
| :ESE1 | <Mask value> | Writing and reading event status enable register 1 | | |
| :ESE1? | |
| :ESE2 | <Mask value> | Writing and reading event status enable register 2 | | |
| :ESE2? | |
| :ESE3 | <Mask value> | Writing and reading event status enable register 3 | | |
| :ESE3? | |
| :ESR0? | | Reading event status register 0 | | |
| :ESR1? | | Reading event status register 1 | | |
| :ESR2? | | Reading event status register 2 | | |
| :ESR3? | | Reading event status register 3 | | |
Measurement Mode |
| :MODE | <LCR/CONTinuous> | Setting and querying measurement mode | | |
| :MODE? | |
Measurement Frequency |
| :FREQuency | <Frequency> | Setting and querying the Measurement Frequency | | |
| :FREQuency? | |
Measurement Range |
| :RANGe | <Range No.> | Setting and querying the measurement range | | |
| :RANGe? | |
| :RANGe:AUTO | <ON/OFF> | Automatically setting and querying the measurement range | | |
| :RANGe:AUTO? | |
| :RANGe:AUTO:LIMit | <RST/lower limit range>,<upper limit range> | Setting and querying the AUTO range limit function | | |
| :RANGe:AUTO:LIMit? | |
| :RANGe:JSYNc | <ON/OFF> | Setting and querying the JUDGE synchronization setting | | |
| :RANGe:JSYNc? | |
| :RANGe:LOWZ | <ON/OFF> | Setting and querying low Z high accuracy mode | | |
| :RANGe:LOWZ? | |
| :RANGe:SYNC | <ON/OFF> | Setting and querying the range synchronization function | | |
| :RANGe:SYNC? | |
| :RANGe:SYNC:AVERaging | <ALL/Range No.>,<OFF/number of averaging times> | Setting and querying the number of measurement averaging time for the range synchronization function | | |
| :RANGe:SYNC:AVERaging? | <Range No.> |
| :RANGe:SYNC:SPEEd | <ALL/Range No.>,<FAST/MEDium/SLOW/SLOW2> | Setting and querying the measurement speed for the range synchronization function | | |
| :RANGe:SYNC:SPEEd? | <Range No.> |
| :RANGe:SYNC:TRIGger:DELay | <ALL/Range No.>,<Trigger delay time> | Setting and querying the trigger delay time for the range synchronization function | | |
| :RANGe:SYNC:TRIGger:DELay? | <Range No.> |
| :RANGe:SYNC:SSOurce | <ALL/Range No.>,<ON/OFF> | Setting and querying the trigger synchronous output function for the range synchronization function | | |
| :RANGe:SYNC:SSOurce? | <Range No.> |
| :RANGe:SYNC:SSOurce:WAIT | <ALL/Range No.>,<Wait time> | Setting and querying the wait time of the trigger synchronous output function for the range synchronization function | | |
| :RANGe:SYNC:SSOurce:WAIT? | <Range No.> |
Measurement Signal Level |
| :LEVel | <V/CV/CC> | Setting and querying the measurement signal level | | |
| :LEVel? | |
Constant current level |
| :LEVel:CCURRent | <Constant current level> | Setting and querying the constant current level value | | |
| :LEVel:CCURRent? | |
Constant voltage level |
| :LEVel:CVOLTage | <Constant voltage level> | Setting and querying the constant voltage level | | |
| :LEVel:CVOLTage? | |
Open-circuit voltage level |
| :LEVel:VOLTage | <Open-circuit voltage level> | Setting and querying the open-circuit voltage level | | |
| :LEVel:VOLTage? | |
Measurement Speed |
| :SPEEd | <FAST/MEDium/SLOW/SLOW2> | Setting and querying the measurement speed | | |
| :SPEEd? | |
Limit Function of Measurement Signal Level |
| :LIMiter | <ON/OFF> | Setting and querying the limit function | | |
| :LIMiter? | |
| :LIMiter:CURRent | <Current limit value> | Setting and querying the current limit value | | |
| :LIMiter:CURRent? | |
| :LIMiter:VOLTage | <Voltage limit value> | Setting and querying the voltage limit value | | |
| :LIMiter:VOLTage? | |
Average Function |
| :AVERaging | <OFF/ number of averaging times> | Setting and querying measurement averaging | | |
| :AVERaging? | |
DC bias function |
| :DCBias | <ON/OFF> | Setting and querying ON/ OFF of DC bias function | | |
| :DCBias? | |
| :DCBias:LEVel | <DC bias level> | Setting and querying the DC bias level | | |
| :DCBias:LEVel? | |
Trigger |
| :TRIGger | <INTernal/EXTernal> | Setting and querying the trigger mode | | |
| :TRIGger? | |
| :TRIGger:DELay | <Trigger delay time> | Setting and querying the trigger delay time | | |
| :TRIGger:DELay? | |
Trigger Synchronous Output Function |
| :SSOurce | <ON/OFF> | Setting and querying the trigger synchronous output function | | |
| :SSOurce? | |
| :SSOurce:WAIT | <Wait time> | Setting and querying the wait time of trigger synchronous output | | |
| :SSOurce:WAIT? | |
DC Resistance Measurement Function |
| :DCResistance:RANGe | <Range No.> | Setting and querying the measurement range for when DC resistance measurement | | |
| :DCResistance:RANGe? | |
| :DCResistance:RANGe:AUTO | <ON/OFF> | Automatically setting and querying the measurement range for when DC resistance measurement | | |
| :DCResistance:RANGe:AUTO? | |
| :DCResistance:RANGe:AUTO:LIMit | <RST/lower limit range>,<upper limit range> | Setting and querying the AUTO range limit function during DC resistance measurement | | |
| :DCResistance:RANGe:AUTO:LIMit? | |
| :DCResistance:RANGe:LOWZ | <ON/OFF> | Setting and querying low Z high accuracy mode for when DC resistance measurement | | |
| :DCResistance:RANGe:LOWZ? | |
| :DCResistance:RANGe:JSYNc | <ON/OFF> | Setting and querying the JUDGE synchronization setting during DC resistance measurement | | |
| :DCResistance:RANGe:JSYNc? | |
| :DCResistance:RANGe:SYNC:AVERaging | <ALL/Range No.>,<OFF/number of averaging times> | Setting and querying the number of measurement averaging time for the range synchronization function during DC resistance measurement | | |
| :DCResistance:RANGe:SYNC:AVERaging? | <Range No.> |
| :DCResistance:RANGe:SYNC:SPEEd | <ALL/Range No.>,<FAST/MEDium/SLOW/SLOW2> | Setting and querying the measurement speed for the range synchronization function during DC resistance measurement | | |
| :DCResistance:RANGe:SYNC:SPEEd? | <Range No.> |
| :DCResistance:SPEEd | <FAST/MEDium/SLOW/SLOW2> | Setting and querying the measurement speed for when DC resistance measurement | | |
| :DCResistance:SPEEd? | |
| :DCResistance:AVERaging | <OFF/ number of averaging times> | Setting and querying averaging for when DC resistance measurement | | |
| :DCResistance:AVERaging? | |
| :DCResistance:ADJust | <ON/OFF> | Setting and querying the DC offset for when DC resistance measurement | | |
| :DCResistance:ADJust? | |
| :DCResistance:ADJust:DEMand | | Acquiring DC offset for when DC resistance measurement | | |
| :DCResistance:ADJDelay | <Adjustment Delay time> | Setting and querying the adjustment delay time during DC resistance measurement | | |
| :DCResistance:ADJDelay? | |
| :DCResistance:DCDelay | <DC Delay time> | Setting and querying the DC delay time during DC resistance measurement | | |
| :DCResistance:DCDelay? | |
| :DCResistance:LFRequency | <Line Frequency> | Setting and querying the line frequency during DC resistance measurement | | |
| :DCResistance:LFRequency? | |
Judgment Function |
| :JUDGment | | Setting and querying the judgment function | | |
| :JUDGment? | |
Comparator Function |
| :COMParator | <OFF/ON> | Setting and querying ON/ OFF of comparator function | | |
| :COMParator? | |
| :COMParator:FLIMit:ABSolute | <OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the first parameter of the comparator function (absolute value mode) | | |
| :COMParator:FLIMit:ABSolute? | |
| :COMParator:FLIMit:DEViation | <Reference value>,<OFF/ Lower limit values>,<OFF/ Upper limit values> | Setting and querying the reference value and the upper and lower limit values of the first parameter of the comparator function (deviation percentage (Ģ%) mode) | | |
| :COMParator:FLIMit:DEViation? | |
| :COMParator:FLIMit:MODE | <ABSolute/PERcent/DEViation> | Setting and querying the judgment mode of the first parameter of the comparator function | | |
| :COMParator:FLIMit:MODE? | |
| :COMParator:FLIMit:PERcent | <Reference value>,<OFF/ Lower limit values>,<OFF/ Upper limit values> | Setting and querying the reference value and the upper and lower limit values of the first parameter of the comparator function (percentage (%) mode) | | |
| :COMParator:FLIMit:PERcent? | |
| :COMParator:SLIMit:ABSolute | <OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the third parameter of the comparator function (absolute value mode) | | |
| :COMParator:SLIMit:ABSolute? | |
| :COMParator:SLIMit:DEViation | <Reference value>,<OFF/ Lower limit values>,<OFF/ Upper limit values> | Setting and querying the reference value and the upper and lower limit values of the SUB parameter of the comparator function (deviation percentage (Ģ%) mode) | | |
| :COMParator:SLIMit:DEViation? | |
| :COMParator:SLIMit:MODE | <ABSolute/PERcent/DEViation> | Setting and querying the judgment mode of the third parameter of the comparator function | | |
| :COMParator:SLIMit:MODE? | |
| :COMParator:SLIMit:PERcent | <Reference value>,<OFF/ Lower limit values>,<OFF/ Upper limit values> | Setting and querying the reference value and the upper and lower limit values of the third parameter of the comparator function (percentage mode) | | |
| :COMParator:SLIMit:PERcent? | |
BIN Function |
| :BIN | <OFF/ON> | Setting and querying ON/ OFF of BIN function | | |
| :BIN? | |
| :BIN:FLIMit:ABSolute | <BIN number>,<OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the first parameter of the BIN function (absolute value mode) | | |
| :BIN:FLIMit:ABSolute? | <BIN number> |
| :BIN:FLIMit:DEViation | <BIN number>,<OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the first parameter of the BIN function (deviation percentage (Ģ%) mode) | | |
| :BIN:FLIMit:DEViation? | <BIN number> |
| :BIN:FLIMit:MODE | <ABSolute/PERcent/DEViation> | Selecting and querying the mode of the first parameter of the BIN function | | |
| :BIN:FLIMit:MODE? | |
| :BIN:FLIMit:PERcent | <BIN number>,<OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the first parameter of the BIN function (percentage (%) mode) | | |
| :BIN:FLIMit:PERcent? | <BIN number> |
| :BIN:FLIMit:REFerence | <Reference value> | Setting and querying the reference value of the first parameter of the BIN function (percentage (%) mode and deviation percentage (Ģ%) mode) | | |
| :BIN:FLIMit:REFerence? | |
| :BIN:SLIMit:ABSolute | <BIN number>,<OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the third parameter of the BIN function (absolute value mode) | | |
| :BIN:SLIMit:ABSolute? | <BIN number> |
| :BIN:SLIMit:DEViation | <BIN number>,<OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the third parameter of the BIN function (deviation percentage (Ģ%) mode) | | |
| :BIN:SLIMit:DEViation? | <BIN number> |
| :BIN:SLIMit:MODE | <ABSolute/PERcent/DEViation> | Selecting and querying the mode of the third parameter of the BIN function | | |
| :BIN:SLIMit:MODE? | |
| :BIN:SLIMit:PERcent | <BIN number>,<OFF/ lower value>,<OFF/ upper value> | Setting and querying the upper and lower limit values of the third parameter of the BIN function (percentage (%) mode) | | |
| :BIN:SLIMit:PERcent? | <BIN number> |
| :BIN:SLIMit:REFerence | <Reference value> | Setting and querying the reference value of the third parameter of the BIN function (percentage (%) mode and deviation percentage (Ģ%) mode) | | |
| :BIN:SLIMit:REFerence? | |
Measurement Value Output |
| :MEASure? | | Querying measurement data | | |
| :MEASure:OUTPut:AUTO | <ON/OFF> | Setting and querying the measurement value automatic output function | | |
| :MEASure:OUTPut:AUTO? | |
| :MEASure:VALid | <Setting value> | Setting and querying the response data of the measurement acquisition query | | |
| :MEASure:VALid? | |
| :MEASure:ITEM | <MR0>, <MR1>, <MR2> | Setting and querying measurement parameters | | |
| :MEASure:ITEM? | |
Parameter Settings (# is a numerical value from 1 to 4) |
| :PARameter# | <Z/ Y/ PHASE(phase angle)/ CS/ CP/ D/ LS/ LP/ Q/ RS/ G/ RP/ X/ B/ RDC/ S/ E/ OFF> | Setting and querying the display parameters | | |
| :PARameter#? | |
| :PARameter#:DIGit | <Number of display digits> | Setting and querying number of display digits | | |
| :PARameter#:DIGit? | |
Open / Short Compensation Range |
| :CORRection:LIMit:DC | <ON/OFF> | Open / Short compensation function on/off setting and querying during DC measurement | | |
| :CORRection:LIMit:DC? | |
| :CORRection:LIMit:POINt | <UNLimited/Compensation minimum frequency>, <UNLimited/Compensation maximum frequency> | Open / Short compensation range setting and querying during AC measurement | | |
| :CORRection:LIMit:POINt? | |
Open-circuit Compensation Function |
| :CORRection:OPEN | <OFF/ALL/SPOT/CANCel> | Executing, cancelling, and querying the open compensation function | | |
| :CORRection:OPEN? | |
| :CORRection:OPEN:ERRor? | | Querying open compensation failure flag | | |
| :CORRection:OPEN:FREQuency | <Compensation No.>,<OFF/ DC/ Frequency> | Setting and querying frequency for acquiring open compensation value | | |
| :CORRection:OPEN:FREQuency? | <Compensation No.> |
| :CORRection:OPEN:RETurn | <OFF/ALL/SPOT> | Setting and querying the open compensation function | | |
| :CORRection:OPEN:RETurn? | |
| :CORRection:OPEN:DATA:ALL? | | Open compensation value inquiry (all compensation) | | |
| :CORRection:OPEN:DATA:SPOT? | <Compensation No.> | Open compensation value inquiry (spot compensation) | | |
Short Circuit Compensation Function |
| :CORRection:SHORt | <OFF/ALL/SPOT/CANCel> | Executing, cancelling, and querying the short compensation function | | |
| :CORRection:SHORt? | |
| :CORRection:SHORt:ERRor? | | Querying short compensation failure flag | | |
| :CORRection:SHORt:FREQuency | <Compensation No.>,<OFF/ DC/ Frequency> | Setting and querying frequency for acquiring short compensation value | | |
| :CORRection:SHORt:FREQuency? | <Compensation No.> |
| :CORRection:SHORt:RETurn | <OFF/ALL/SPOT> | Setting and querying the short compensation function | | |
| :CORRection:SHORt:RETurn? | |
| :CORRection:SHORt:DATA:ALL? | | Short compensation value inquiry (all compensation) | | |
| :CORRection:SHORt:DATA:SPOT? | <Compensation No.> | Short compensation value inquiry (spot compensation) | | |
Load Compensation Function |
| :CORRection:LOAD | <OFF/ON> | Executing and querying the load compensation function | | |
| :CORRection:LOAD? | |
| :CORRection:LOAD:CONDition | <Compensation No.>,<Frequency>,<Range No.>,<LOW Z>,<V/ CV /CC>,<Level value>,<DC bias>,<DC bias value> | Setting and querying the load compensation conditions | | |
| :CORRection:LOAD:CONDition? | <Compensation No.> |
| :CORRection:LOAD:DCResistance:CONDition | <Compensation No.>,<Range No.>,<LOW Z> | Setting and querying the load compensation conditions for when DC resistance measurement | | |
| :CORRection:LOAD:DCResistance:CONDition? | <Compensation No.> |
| :CORRection:LOAD:DCResistance:REFerence | <Compensation No.>,<Reference value> | Setting and querying the reference value of load compensation for when DC resistance measurement | | |
| :CORRection:LOAD:DCResistance:REFerence? | <Compensation No.> |
| :CORRection:LOAD:DATA? | <Compensation No.> | Load compensation value inquiry | | |
| :CORRection:LOAD:ERRor? | | Querying load compensation failure flag | | |
| :CORRection:LOAD:REFerence | <Compensation No.>,<Mode No.>,<Reference value1>,<Reference value2> | Setting and querying the reference values of load compensation | | |
| :CORRection:LOAD:REFerence? | <Compensation No.> |
| :CORRection:LOAD:RESet | <Compensation No.> | Resetting the load compensation conditions | | |
| :CORRection:LOAD:RETurn | <OFF/ON> | Setting and querying the load compensation function | | |
| :CORRection:LOAD:RETurn? | |
Cable length compensation function |
| :CORRection:CABLe | <Cable length> | Setting and querying the cable length compensation function | | |
| :CORRection:CABLe? | |
Scaling Function |
| :CORRection:SCALe | <OFF/ON> | Setting and querying the scaling compensation function | | |
| :CORRection:SCALe? | |
| :CORRection:SCALe:DATA | <Scaling No.>,<Compensation value A>,<Compensation value B> | Setting and querying the scaling compensation value | | |
| :CORRection:SCALe:DATA? | <Scaling No.> |
Continuous measurement settings |
| :CONTinuous:DRAW | <REAL/AFTer> | Setting and querying the screen display timing | | |
| :CONTinuous:DRAW? | |
| :CONTinuous:EXECution | <Panel No.>, <ON/OFF> | Setting and querying the continuous measurement target | | |
| :CONTinuous:EXECution? | <Panel No.> |
| :CONTinuous:COUNt? | | Panel count targeted for measurement in continuous measurement mode inquiry | | |
Measurement Value Output |
| :MEASure? | <No data/ ALL> | Querying measurement data | | |
| :MEASure:CONTinuous:COMParator? | | Querying the overall judgment result when continuous measurement | | |
Waveform Averaging Function |
| :WAVE | <ON/OFF> | Setting and querying the waveform averaging function | | |
| :WAVE? | |
| :WAVE:NUM | <Frequency No.>,<number of measurement waveforms> | Setting and querying the number of measurement waveforms for the waveform averaging function | | |
| :WAVE:NUM? | <Frequency No.> |
| :WAVE:RESet | <FAST/MEDium/SLOW/SLOW2> | Resets the number of measurement waveforms for the waveform averaging function to that of each measurement speed. | | |
Contact Check Function |
| :CCHeck:VERify | <OFF/BEFore/AFTer/BOTH> | Setting and querying the contact check function | | |
| :CCHeck:VERify? | |
| :CCHeck:SENSitivity | <Settable range> | Setting and querying the settable range for the contact check function | | |
| :CCHeck:SENSitivity? | |
| :CCHeck:DELay | <Delay time> | Setting and querying the contact check delay time | | |
| :CCHeck:DELay? | |
HIGH- Z reject function |
| :HIZ | <ON/OFF> | Setting and querying the Hi Z reject function | | |
| :HIZ? | |
| :HIZ:LIMit | <Limit value> | Setting and querying the limit value of the Hi Z reject function | | |
| :HIZ:LIMit? | |
Measurement Value Memory Function |
| :MEMory? | <No data/ ALL> | Querying measurement values saved to memory with the measurement value memory function | | |
| :MEMory:CLEar | | Clearing memory of measurement value memory function | | |
| :MEMory:CONTrol | <ON/IN/OFF> | Setting and querying the measurement value memory function | | |
| :MEMory:CONTrol? | |
| :MEMory:COUNt? | | Querying the number of measurement values saved to memory with the memory function | | |
| :MEMory:POINts | <Memory size> | Setting and querying the measurement value memory size | | |
| :MEMory:POINts? | |
| :MEMory:SAVE | | Saving of measured value memory | | |
Display Function |
| :DISPlay | <ON/OFF> | Setting and querying LCD display | | |
| :DISPlay? | |
Zoom Function |
| :ZOOM | <ON/OFF> | Setting and querying the zoom function | | |
| :ZOOM? | |
BCD Output Function |
| :IO:BCD | <OFF/ON> | Setting and querying ON/ OFF of BCD output function | | |
| :IO:BCD? | |
| :IO:BCD:DECimal | <Parameter No.>, <Decimal point> | Setting and querying decimal point of BCD output function | | |
| :IO:BCD:DECimal? | <Parameter No.> |
Key Lock |
| :KEYLock | | Executing and querying the key lock | | |
| :KEYLock? | |
| :KEYLock:PASScode | <Passcode/ none> | Setting the key lock passcode | | |
| :KEYLock:UNLock | <Passcode/ none> | Disabling the key lock | | |
Beep Tone |
| :BEEPer:JUDGment | <OFF/IN/NG> | Setting and querying beep sound for the judgment results of measurement values | | |
| :BEEPer:JUDGment? | |
| :BEEPer:KEY | <ON/OFF> | Setting and querying beep sound for key input | | |
| :BEEPer:KEY? | |
| :BEEPer:TONE | <A/B/C/D> | Setting and querying the beep tone type | | |
| :BEEPer:TONE? | |
Calculation Setting of Conductivity/Permittivity |
| :CALCulate:PARameter | <CS/ CP> | Setting and querying the calculation parameters of conductivity/permittivity | | |
| :CALCulate:PARameter? | |
| :CALCulate:LENGth | <Length of conductor> | Setting and querying the conductor length during calculation of conductivity/permittivity | | |
| :CALCulate:LENGth? | |
| :CALCulate:AREA | <Cross-sectional area of conductor> | Setting and querying the cross-sectional area of the conductor during calculation of conductivity/permittivity | | |
| :CALCulate:AREA? | |
Calculation Setting of Conductivity |
| :SIGMa | <Length of conductor>, <Cross-sectional area of conductor> | Setting and querying the length and cross-sectional area of the conductor during calculation of conductivity | | |
| :SIGMa? | |
EXT I/O Output |
| :IO:EOM:MODE | <HOLD/PULSe> | INDEX and EMO output method setting and inquiry | | |
| :IO:EOM:MODE? | |
| :IO:EOM:PULSe | <Pulse width> | Pulse width for which to keep EOM low (on) setting and inquiry | | |
| :IO:EOM:PULSe? | |
| :IO:OUTPut:DELay | <I/O delay time> | Setting and querying the delay time between judgment result output and EOM output | | |
| :IO:OUTPut:DELay? | |
| :IO:RESult:RESet | <ON/OFF> | Setting and querying output of the judgment result signal line | | |
| :IO:RESult:RESet? | |
| :IO:TRIGger:EDGe | <DOWN/UP> | Setting and querying the trigger edge | | |
| :IO:TRIGger:EDGe? | |
| :IO:TRIGger:ENABle | <ON/OFF> | Setting and querying permit/prohibit of trigger input during measurement | | |
| :IO:TRIGger:ENABle? | |
Panel Save Function |
| :SAVE | <Panel No.>,<Panel name> | Executing and querying the panel save function | | |
| :SAVE? | <Panel name> |
| :SAVE:CLEar | <ALL/ Panel No.> | Clearing data saved for a panel | | |
| :SAVE:NAME? | <Panel No.> | Querying a panel name | | |
| :SAVE:REName | <Panel No.>,<Panel name> | Changing a panel name | | |
| :SAVE:TYPE | <ALL/HARDware/ADJust> | Setting and querying the save type | | |
| :SAVE:TYPE? | |
| :SAVE:MODE? | <Panel No.> | Querying the save type | | |
Panel Load Function |
| :LOAD | <Panel No.> | Executing panel load | | |
Message Terminator |
| :TRANsmit:TERMinator | <Terminator number> | Setting and querying the terminator of the response message | | |
| :TRANsmit:TERMinator? | |
RS-232C Communication Handshake |
| :HANDshake | <OFF/HARDware/X/BOTH> | Setting and querying the RS-232C Communication Handshake | | |
| :HANDshake? | |
|
| :FORMat:DATA | <ASCii/REAL> | Setting and querying the data transfer format | | |
| :FORMat:DATA? | |
| :FORMat:LONG | <ON/OFF> | Setting and querying long format for when data transfer | | |
| :FORMat:LONG? | |
|
| :HEADer | <ON/OFF> | Setting and querying existence of header in response message | | |
| :HEADer? | |
System Settings |
| :SYSTem:DATE | <Year>,<Month>,<Day> | Setting and querying the date | | |
| :SYSTem:DATE? | |
| :SYSTem:MACAddress? | | Querying the MAC address | | |
| :SYSTem:SERIAlno? | | Querying the serial number | | |
| :SYSTem:TIME | <Hour>,<Minute>,<Second> | Setting and querying the time | | |
| :SYSTem:TIME? | |
| :SYSTem:USBId? | | Returns the USB ID. | | |
Initialize Device |
| :PRESet | | Initializing the instrument | | |
File storage function |
| :FILE:DATE | <ON/OFF> | Setting and querying the date and time for when saving text | | |
| :FILE:DATE? | |
| :FILE:DELIMiter | <COMma/TAB/SEMIcolon/SPACE> | Setting and querying the delimiter for when saving text | | |
| :FILE:DELIMiter? | |
| :FILE:FOLDer | <Folder name> | Setting and querying the save folder | | |
| :FILE:FOLDer? | |
| :FILE:INFOrmation? | | Querying USB flash drive information | | |
| :FILE:MODE | <AUTO/MANUAL> | Setting and querying the mode of the save folder | | |
| :FILE:MODE? | |
| :FILE:PANel:SAVE | <Panel name> | Execution of panel save to USB memory | | |
| :FILE:PANel:LOAD | <Panel name> | Execution of panel load from USB memory | | |
| :FILE:PANel:ALLSave | <Specified save folder name> | Execution of all save to USB memory | | |
| :FILE:PANel:ALLLoad | <Specified save folder name> | Execution of all load from USB memory | | |
| :FILE:PARAmeter | <ON/OFF> | Setting and querying the measurement parameter setting for when saving text | | |
| :FILE:PARAmeter? | |
| :FILE:QUOTe | <OFF/DOUBle/SINGle> | Setting and querying the quotation mark setting for when saving text | | |
| :FILE:QUOTe? | |
| :FILE:SAVE | | Executing file saving | | |
| :FILE:SET | <ON/OFF> | Setting and querying the measurement condition setting for when saving text | | |
| :FILE:SET? | |
| :FILE:TYPE:TEXT | <OFF/ON> | Text save settings and inquiry | | |
| :FILE:TYPE:TEXT? | |
| :FILE:TYPE:BMP | <OFF/COLor/MONochrome> | BMP save settings and inquiry | | |
| :FILE:TYPE:BMP? | |
Monitor Function |
| :MONItor? | | Querying the voltage/current monitor value | | |
Screen storage function |
| :HCOPy:DATA? | <COLor/MONochrome> | Acquiring the BMP data of the measurement screen | | |