Battery Tester | BT3562A

Key Features • Simultaneous measurement of internal resistance and open circuit voltage. • Fully automated production line testing of large cells for xEVs or mid-sized packs of up to 100 V. • Resistance measurement ranges: 3 mΩ/30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ • Voltage measurement ranges: 6 V/60 V/100 V • Equipped with LAN

Model No. (Order Code)

BT3562A

Note: Measurement leads are not included. Purchase the appropriate lead option for your application separately. The male (system side) of the EXT I/O connector is also available. Please contact your authorized Hioki distributor or reseller.

Measuring battery performance and safety using internal resistance (AC-IR) and open-circuit voltage (OCV)

Inspect the quality of completed cells, modules, and packs on production lines. Measure internal resistance (AC-IR) and open-circuit voltage (OCV) to check battery quality. Cells produced at the cell production factory are shipped to the module production factory after undergoing a shipping inspection. Since factors such as vibrations during shipment and even the passage of time can cause defects, batteries undergo an acceptance inspection before being assembled into modules and packs. BT3561A Small cells for power motors, Small packs of up to 60 V Voltage measurement ranges: 6 V/60 V Resistance measurement ranges: 30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ BT3562A Large cells for xEVs, Mid-sized packs of up to 100 V Voltage measurement ranges: 6 V/60 V/100 V Resistance measurement ranges: 3 mΩ/30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ BT3563A Large packs for xEVs, Large packs of up to 300 V Voltage measurement ranges: 6 V/60 V/300 V Resistance measurement ranges: 3 mΩ/30 mΩ/300 mΩ/3 Ω/30 Ω/300 Ω/3 kΩ

Reducing test system development cost and management man-hours

The new BT356xA has dramatically improved tolerances for line resistance compared to previous models. This improvement makes it easy to build test systems with large numbers of channels using relays. Additionally, a longer maintenance cycle for systems in use means fewer maintenance man-hours. Finally, its capability to handle thinner cables than with previous models* makes it easier to route cables. *AWG 29 (0.064 mm2) wire equivalent to 2.2 Ω over an 8 m round trip can be used with the 3 mΩ or 30 mΩ range.

Improve Productivity by Increasing the Number of Inspection Channels

You can use the Switch Mainframe SW1001/SW1002 to increase the number of measurement channels. Additionally, you can perform scan measurement by controlling two instruments at once, for example a BT356xA series instrument and a DM7276, or a BT4560 and a DM7276.

Preventing instrument malfunctions caused by static electricity

Batteries can become charged on production lines, for example, when being transported on a conveyor belt. When probes are placed in contact with such batteries, the resulting application of static electricity can then damage the instrument. The BT356xA series is designed to withstand contact with ±30 kV of static electricity*, preventing static-caused malfunctions and reducing testing line downtime. * ±30 kV IEC 61000-4-2 contact discharge

LAN interface as standard

The BT356xA series is equipped with a LAN interface as standard equipment, making it easy for the instrument to interoperate with a PLC*-based control system. The ability to use readily accessible LAN cables helps lower costs during system development and maintenance. Furthermore, a design with strong noise and static electricity resistance helps avoid system problems. *Programmable Logic Controller, a device that automatically controls one or more machines

The De Facto Standard of Battery Testers

The HIOKI BT356xA series These highly advanced battery testers are best suited for shipping and acceptance inspections of cells and battery packs. They simultaneously measure internal resistance and the battery’s open-circuit voltage (OCV). Since the AC-IR measurement method is used, the measurement time is shortened. In addition, highly repeatable results are attained with this method. These testers have a highly accurate 3 mΩ range, allowing for a resistance measurement of battery tab welding and bus bars. All of this combines for the best choice in battery testers. High input voltage applications The input high voltage (1,000 V) model, BT3564, can measure the total resistance of the battery whole pack at once. *Watch with the video subtitles on, to see detailed descriptions.

Basic specifications (Accuracy guaranteed for 1 year, Accuracy guarantee period after adjustment made by Hioki: 1 year)

Resistance measurement ranges	3 mΩ（Max. display: 3.1000 mΩ, resolution: 0.1 μΩ, measurement current: 100 mA） 30 mΩ（Max. display: 31.000 mΩ, resolution: 1 μΩ, measurement current: 100 mA） 300 mΩ（Max. display: 310.00 mΩ, resolution: 10 μΩ, measurement current: 10 mA） 3 Ω（Max. display: 3.1000 Ω, resolution: 100 μΩ, measurement current: 1 mA） 30 Ω（Max. display: 31.000 Ω, resolution: 1 mΩ, measurement current: 100 μA） 300 Ω（Max. display: 310.00 Ω, resolution: 10 mΩ, measurement current: 10 μA） 3 kΩ（Max. display: 3.1000 kΩ, resolution: 100 mΩ, measurement current: 10 μA） Basic accuracy: ±0.5% rdg ±10 dgt（3 mΩ range）, ±0.5% rdg ±5 dgt（30 mΩ range or more） Measurement frequency: 1 kHz ±0.2 Hz Measurement method: AC four-terminal method
Voltage measurement ranges	6 V（Max. display: 6.00000 V, resolution: 10 μV） 60 V（Max. display: 60.0000 V, resolution: 100 μV） 100 V（Max. display: 100.000 V, resolution: 1 mV） Basic accuracy: ±0.01% rdg. ±3 dgt.
Response time	10 ms
Sampling period	Ω or V (60 Hz): 4 ms (EX.FAST), 12 ms (FAST), 35 ms (MEDIUM), 150 ms (SLOW) ΩV (60 Hz): 8 ms (EX.FAST), 24 ms (FAST), 70 ms (MEDIUM), 253 ms (SLOW) Ω or V (50 Hz): 4 ms (EX.FAST), 12 ms (FAST), 42 ms (MEDIUM), 157 ms (SLOW) ΩV (50 Hz): 8 ms (EX.FAST), 24 ms (FAST), 84 ms (MEDIUM), 259 ms (SLOW)
Functions	Contact check, Zero adjustment (±1000 counts), Pulse measurement, Comparator (Hi/ IN/ Lo), Statistical calculations (Max. 30,000), Delay, Average, Panel saving/loading, Memory storage, LabVIEW® driver
Interfaces	LAN (TCP/IP, 10BASE-T/100BASE-TX) RS-232C (Max. 38.4 kbps, Available as printer I/F) EXT I/O (37-pin Handler interface) Analog output (DC 0 V to 3.1 V)
Power supply	100 to 240 V AC, 50 Hz/60 Hz, 35 VA max.
Dimensions and mass	215 mm (8.46 in) W × 80 mm (3.15 in) H × 295 mm (11.61 in) D, 2.4 kg (84.7 oz)

Log into your myHioki account to access more technical documents and information where available.

Seminar Videos On Demand

No results were found.

Seminar Schedule

No results were found.

Catalogs

Preview: BATTERY HiTESTER BT3561A, BT3562A, BT3563A	Download PDF [1MB]	English
Catalog: BATTERY TESTER Series	Download PDF [8MB]	English

User Guides

Electrical Measurements of Lithium-Ion Batteries	Download PDF [4MB]	English
Lead-acid Battery Handbook	Download PDF [1MB]	English

Manuals

If you can not download, log into your myHioki account to access more technical documents and information where available.

BATTERY HiTESTER BT3561A,BT3562,BT3562-01,BT3562A,BT3563,BT3563-01,BT3563A [4MB]	Instruction Manual	Simplified Chinese	Ver.06
BATTERY HiTESTER BT3561A,BT3562,BT3562-01,BT3562A,BT3563,BT3563-01,BT3563A [5MB]	Instruction Manual	Korean	Ver.04
BATTERY HiTESTER BT3561A,BT3562,BT3562-01,BT3562A,BT3563,BT3563-01,BT3563A [7MB]	Instruction Manual	English	Ver.09
BATTERY HiTESTER BT3561A,BT3562,BT3562-01,BT3562A,BT3563,BT3563-01,BT3563A [5MB]	Instruction Manual	French	Ver.04
BATTERY HiTESTER BT3561A,BT3562,BT3562-01,BT3562A,BT3563,BT3563-01,BT3563A [5MB]	Instruction Manual	German	Ver.04

Outline Drawings

If you can not download, log into your myHioki account to access more technical documents and information where available.

BATTERY HiTESTER BT3562A [78KB]

Ver.00

Technical Notes

No results were found.

Declaration of Conformity

BATTERY HiTESTER BT3561A,BT3562A,BT3563A [30KB]

Ver.00

Drivers, Firmware

LabVIEW driver for BATTERY HiTESTER 3561,BT3562,BT3563,BT3564,BT3561A,BT3562A, BT3563A	Freeware	Version 1.01
BATTERY HiTESTER Sample Application	Freeware	Version 2.00