Multiplexer | SWITCH MAINFRAME SW1002

The SW1002 is a switch mainframe for housing the SW9001 or SW9002 Multiplexer Module to deliver quick, multi-channel battery testing. Connect up to 2 battery testing instruments to test OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Key Features • Switch between voltmeter and battery tester while testing • SW1002: max. 264 channels (2-wire) to max. 72 channels (4-terminal pair) • Circuit-design-friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*) * For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz • For OCV measurement, internal resistance measurement, and external potential measurement of battery cells • Measure battery modules up to 60 V DC

Model No. (Order Code)

SW1002	12 slots

Note: Multiplexer Modules not included with the Switch Mainframe SW1001 / SW1002. Modules must be purchased separately.

Multi-channel Battery Testing.Packed with Features to Ensure Accuracy

Combine the SW1002 with a battery testing instrument to measure a battery cell's OCV (open circuit voltage), internal resistance, reaction resistance at low frequency, Cole-Cole plot, and external potential on multiple channels.

Connect Up to Two Measuring Instruments with Different Functions

Switch between two types of measuring instruments to perform a variety of measurements.

Battery Measurement Supported by Exclusive PC Application

Use the free, downloadable PC application to perform various measurements easily.

Circuit Design for Impedance Measurements

The effect on the detection signal is reduced by canceling the magnetic flux of the AC measurement current and separating the source from the sense.

Choose from Two Types of Multiplexer Modules

MULTIPLEXER MODULE SW9001:This module supports 2-wire/4-wire configurations. Channel switching can be performed in 11 ms (excluding communication, command processing time, and contact bounce). MULTIPLEXER MODULE SW9002: This module supports 4-terminal pair configuration for use in combination with BT4560 and IM3590. 2-wire measurement is also possible (Sense only). Channel switching can be performed in 11 ms (excluding communication, command processing time, and contact bounce).

Communication Command Transmission Function Reduces the Number of PC Ports Needed

Normally, PC control requires two ports: one communication port for switching and one for the measuring instrument. By using the communication command transmission function on the SW1002 the switch mainframe can transfer control commands from the PC to the measuring instrument (and responses can be received from the device). This allows you to reduce the number of communication ports used on the measuring instrument

Scan Function

This function switches between channels in order based on the scan list registered in advance. The switch mainframe and the EXT. I/O of the measuring instrument are connected. With the scan function, channel switching and trigger measurement can be synced for continuous scanning.

Basic specifications

Slots	12 slots
Supported modules	MULTIPLEXER MODULE SW9001 (2-wire/4-wire) MULTIPLEXER MODULE SW9002 (4-terminal pair)
Connectible instruments	Max. 2 units 2-wire × 1 + 4-wire × 1, or 2-wire × 1 + 4-terminal pair × 1
Max. input voltage	60 V DC (Cannot connect to battery packs in excess of 60 V DC), 30 V AC rms, 42.4 V peak, Maximum rated voltage to ground: 60 V DC
Communication I/F	LAN, USB, RS-232C (for host, for measurement instruments)
Functions	Channel switching, wiring method, scan function, communication command transmission, channel delay, shield switching
Power supply	100 to 240 V AC / 30 VA (50/60 Hz)
Dimensions and mass	430 mm (16.93 in) W × 132 mm (5.20 in) H × 420 mm (16.54 in) D, 6.0 kg (211.6 oz)
Accessories	Power cord ×1, instruction manual ×1, usage precautions ×1, USB driver CD ×1

Basic specifications for MULTIPLEXER MODULE

	SW9001	SW9002
Wiring method	2-wire or 4-wire	4-terminal pair (6-wire) or 2-wire
No. of channels	22 channels (2-wire) / 11 channels (4-wire)	6 channels (4-terminal pair) / 6 channels (2-wire)
Contact method	Armature relays
Channel switching time	11 ms (excluding measurement time)
Max. allowable voltage	60 V DC, 30 V AC rms, 42.4 V peak
Max. allowable current	1 A DC, 1 A AC rms	1 A DC, 1 A AC rms (Sense), 2 A DC, 2 A AC rms (Source, Return)
Max. allowable power	30 W (resistive load)
Maximum rated voltage to ground	60 V DC
Dimensions and mass	25.5 mm (1.00 in) W × 110 mm (4.33 in) H × 257 mm (10.12 in) D, 210 g (7.4 oz)	25.5 mm (1.00 in) W × 110 mm (4.33 in) H × 257 mm (10.12 in) D, 196 g (6.9 oz)
Accessories	Instruction manual ×1

Log into your myHioki account to access more technical documents and information where available.

Seminar Videos On Demand

No results were found.

Seminar Schedule

	Energy Plus 2019 - Seoul, Korea	Oct 16, 2019 - Oct 18, 2019
	ENTECH 2019 - Busan, Korea	Sep 18, 2019 - Sep 20, 2019
	Coil Winding Expo - Berlin, Germany	May 21, 2019 - May 23, 2019
	Automotive Testing Expo - Stuttgart, Germany	May 21, 2019 - May 23, 2019
	Batterietage NRW - Aachen, Germany	Apr 2, 2019 - Apr 4, 2019
	PCIM - Nuremberg, Germany	May 7, 2019 - May 9, 2019

Catalogs

Catalog: SWITCH MAINFRAME SW1001, SW1002

Download PDF [3MB]

English

User Guides

No results were found.

Manuals

If you can not download, log into your myHioki account to access more technical documents and information where available.

SWITCH MAINFRAME SW1001,SW1002 [5MB]	Instruction Manual	English	Ver.00
SWITCH MAINFRAME SW1001,SW1002 [170KB]	License Information	Japanese English	Ver.00
SWITCH MAINFRAME SW1001,SW1002 [23MB]	Instruction Manual	Korean	Ver.00
SWITCH MAINFRAME SW1001,SW1002 [23MB]	Instruction Manual	Simplified Chinese	Ver.00