Japanese Chinese Korea
MEMORY HiCORDER 8826 < Recorder < Products
Recorder (For simultaneous recording of multiple signals)

MEMORY HiCORDER 8826

OVERVIEW OPTION DOWNLOAD CATALOG EXTRAS  
Factory-installed option *Must specify when ordering
MEMORY BOARD 9599
MEMORY BOARD 9599 Expands main unit memory by 4×
Note: user installable this board
MO UNIT 9598
Discontinued
Input modules
Input cables are not supplied. Please purchase the appropriate cable for the intended application.
Install by inserting into the main unit. Can be replaced by user.
ANALOG UNIT 8936
ANALOG UNIT 8936 2ch, Voltage input, DC to 400kHz band width
Details
VOLTAGE/TEMP UNIT UNIT 8937
VOLTAGE/TEMP UNIT UNIT 8937 2ch, Voltage or Temperature input with thermocouple
Details
FFT ANALOG UNIT 8938
FFT ANALOG UNIT 8938 2ch, Voltage input, DC to 400kHz band width, built in filter for FFT
Details
STRAIN UNIT 8939
STRAIN UNIT 8939 2ch, Distortion measurement for strain gauge converter
Details
F/V UNIT 8940
F/V UNIT 8940 2ch, Frequency, Voltage input, Current input with clamp-on sensor,
...(8826 Ver. 2.10 or later can be used, Current probes with a serial number of No. 1999-0338386 or later can be used, older types cannot be used.)
Details
4ch ANALOG UNIT 8946
4ch ANALOG UNIT 8946 4ch, Low voltage input, DC to 100kHz band width, ...(it cannot be used with the 8826.)
Details
CHARGE UNIT 8947
CHARGE UNIT 8947 2 ch, Charge-output type piezoelectric acceleration pick-up sensor, Acceleration pick-up sensor with an internal preamp, ...(used with the 8826, Ver. 2.20 or later)
Details
Logic Signal Measurement
LOGIC PROBE 9320
LOGIC PROBE 9320 4-channel type, for voltage/contact signal ON/OFF detection (response time 0.5μsec, large terminal type)
Details
LOGIC PROBE 9321
LOGIC PROBE 9321 4 isolated channels, ON/OFF detection of AC/DC voltage (large terminal type)
Details
Voltage measurement (for use with general input modules)
CONNECTION CORD 9790 (Thin Type)
CONNECTION CORD 9790 (Thin Type) CAT II 300 V, ultraflexible 2.8mm (0.11in) diameter test lead cable, 1.5m (4.92ft) length
Note: Attachment clips sold separately.
ALLIGATOR CLIP 9790-01
ALLIGATOR CLIP 9790-01 Red/black set attaches to the ends of test leads (9790)
GRABBER CLIP 9790-02
GRABBER CLIP 9790-02 Red/black set attaches to the ends of test leads (9790)
CONTACT PIN 9790-03
CONTACT PIN 9790-03 Red/black set attaches to the ends of test leads (9790)
CONNECTION CORD 9198
CONNECTION CORD 9198 For low voltage (up to 300V), 1.7m (5.58ft) length
CONNECTION CORD 9197
CONNECTION CORD 9197 For high voltage (up to 500V), 1.8m (5.91ft) length
10:1 PROBE 9665
10:1 PROBE 9665 Max. rated voltage to earth is same as for input module, max. input voltage 1kV rms (up to 500kHz), 1.5m (4.92ft) length
Details
100:1 PROBE 9666
100:1 PROBE 9666 Max. rated voltage to earth is same as for input module, max. input voltage 5kV peak (up to 1MHz), 1.5m (4.92ft) length
Details
High-Voltage measurement (for use with power supply)
DIFFERENTIAL PROBE 9322
DIFFERENTIAL PROBE 9322 For up to 2kV DC or 1kV AC. Use with either AC Adapter 9418-15, or via Power Cord.
Details
AC ADAPTER 9418-15
AC ADAPTER 9418-15 For powering Differential probe 9322, 100 to 240V AC
POWER CORD 9324
POWER CORD 9324 Use to the 9322 from the logic terminal.
Note: that usage restrictions apply.
POWER CORD 9325
POWER CORD 9325 Use to the 9322 from the F/V UNIT 8940.
Note: that usage restrictions apply.
PT 9303
PT 9303 Insulation transformer, 400V or 200V AC input, 10V AC output, for AC power line measurement. Required along with the Conversion Adapter 9199. Not CE marked
Details
Current measurement (To connect the clamp-on sensor via the conversion cable, The 3274, 3275, and 3276 cannot be used for the F/V UNIT 8940)
UNIVERSAL CLAMP ON CT 9279
UNIVERSAL CLAMP ON CT 9279 Observe waveforms from DC to distorted AC. DC to 20kHz response, input 500A/output 2V AC, Not CE marked
Details
UNIVERSAL CLAMP ON CT 9278
UNIVERSAL CLAMP ON CT 9278 Observe waveforms from DC to distorted AC. DC to 100kHz response, input 200A/output 2V AC
Details
UNIVERSAL CLAMP ON CT 9277
UNIVERSAL CLAMP ON CT 9277 Observe waveforms from DC to distorted AC. DC to 100kHz response, input 20A/output 2V AC
Details
SENSOR UNIT 9555-10
SENSOR UNIT 9555-10 Power supply unit for the 9272 to the 9279 clamp sensors, except for connecting to the F/V unit 8940, for signal output 9217 is necessary.
Details
CLAMP ON SENSOR 9272-10
CLAMP ON SENSOR 9272-10 Enables observation of AC current waveforms. Input: 1 to 100kHz, selectable 20 and 200A rms ranges, 2V AC output
Details
CONVERSION CABLE 9705
CONVERSION CABLE 9705 Use with the Conversion Cable 9318 to connect Model 9272-10 to the F/V Unit 8940. (Not necessary for when using the Model 9272 due to different output wiring specifications.)
CONVERSION CABLE 9318
CONVERSION CABLE 9318 To connect the 9272 to 9279 and the 8940
CONVERSION CABLE 9319
CONVERSION CABLE 9319 To connect the 3273-50 and the 8940
Note: cannot be used with the 3274, 3275, 3276 to connect the 8940 via this cable 9319
CLAMP ON PROBE 3273-50
CLAMP ON PROBE 3273-50 DC to 50MHz wideband response, mA-class current up to 30A rms
Details
Current measurement (Connect directly to the analog input module)
CLAMP ON PROBE 3276
CLAMP ON PROBE 3276 DC to 100MHz wideband response, mA-class current up to 30A rms
Details
CLAMP ON PROBE 3275
CLAMP ON PROBE 3275 DC to 2MHz wideband response, mA-class current up to 500A rms
Details
CLAMP ON PROBE 3274
CLAMP ON PROBE 3274 DC to 10MHz wideband response, mA-class current up to 150A rms
Details
CLAMP ON PROBE 3273-50
CLAMP ON PROBE 3273-50 DC to 50MHz wideband response, mA-class current up to 30A rms
Details
POWER SUPPLY 3272
POWER SUPPLY 3272 Connect and power up to one CLAMP ON PROBE to use in combination with voltage input modules
Details
POWER SUPPLY 3269
POWER SUPPLY 3269 Connect and power up to four CLAMP ON PROBEs to use in combination with voltage input modules
Details
Current measurement * Use for commercial power line, 50/60 Hz (Useless the power supply)
CLAMP ON PROBE 9018-50
CLAMP ON PROBE 9018-50 Enables observation of AC current waveforms. 40Hz to 3kHz response, input 10A to 500A range, output 0.2V AC/range
Details
CLAMP ON PROBE 9132-50
CLAMP ON PROBE 9132-50 Enables observation of AC current waveforms. 40Hz to 1kHz response, input 20A to 1000A range, output 0.2V AC/range
Details
Printer options
RECORDING PAPER 9229
RECORDING PAPER 9229 264mm (10.39in) × 30m (98.43ft), 6rolls set
RECORDING PAPER 9229-01
RECORDING PAPER 9229-01 perforated type, 264mm (10.39in) × 30m (98.43ft), 6 rolls set
PC Communication
LAN CARD
LAN CARD May not operate depending on the environment., 10BASE-T, Not CE marked
LAN COMMUNICATOR 9333
LAN COMMUNICATOR 9333 Application software to create a LAN connection, Compatible with Windows 95/98/Me, Windows NT 4.0/2000/XP
Details
GP-IB CARD 9558
GP-IB CARD 9558 PCMCIA-compliant, cord length: 2m (6.6ft)
RS-232C CARD 9557
RS-232C CARD 9557 PCMCIA-compliant
PC Software
WAVE PROCESSOR 9335
WAVE PROCESSOR 9335 Data conversion, print functions, waveform display, compatible with Windows 95/98/Me, Windows NT 4.0/2000/XP, and Windows Vista 32-bit type.
Details
Removable storage (CF card)
* PC Card Precaution
Use only PC Cards sold by HIOKI. Compatibility and performance are not guaranteed for PC cards made by other manufacturers. You may be unable to read from or save data to such cards.
PC CARD 2G 9830
PC CARD 1G 9729 Supplied with PC Card adapter, 2GB capacity
Details
PC CARD 1G 9729
PC CARD 1G 9729 Supplied with PC Card adapter, 1GB capacity
Details
PC CARD 512M 9728
PC CARD 512M 9728 Supplied with PC Card adapter, 512MB capacity
Details
PC CARD 256M 9727
PC CARD 256M 9727 Supplied with PC Card adapter, 256MB capacity
Details
Other options
CONNECTION CORD 9217
CONNECTION CORD 9217 Cord has insulated BNC connectors at both ends, and connects to insulated BNC connectors on input module. 1.7m (5.58ft) length
CONNECTION CORD 9165
CONNECTION CORD 9165 Cord has metallic BNC connectors at both ends, and connects to metallic BNC connectors. 1.5m (4.92ft) length, Not CE marked
CONVERSION ADAPTER 9199
CONVERSION ADAPTER 9199 Banana-to-BNC, use to connect to BNC terminal on Input Module
LAN CABLE 9642
LAN CABLE 9642 Straight Ethernet cable, supplied with straight to cross conversion cable, 5m (16.41ft) length
OVERVIEW OPTION DOWNLOAD CATALOG EXTRAS